Skip to content

NFAPI

This document describes the SmallCellForum (SCF) (n)FAPI split in 5G, i.e., between the MAC/L2 and PHY/L1. It also describes how to make use of the multiple transport mechanisms between the 2.

The interested reader is recommended to read a copy of the SCF 222.10 specification (“FAPI”). This includes information on what is P5, P7, and how FAPI works. The currently used version is SCF 222.10.02, with some messages upgraded to SCF 222.10.04 due to bugfixes in the spec. Further information about nFAPI can be found in SCF 225.2.0.

Quickstart

Compile OAI as normal. Start the CN and make sure that the VNF configuration matches the PLMN/IP addresses. Then, run the VNF

sudo NFAPI_TRACE_LEVEL=info ./nr-softmodem -O ../../../targets/PROJECTS/GENERIC-NR-5GC/CONF/gnb-vnf.sa.band78.106prb.nfapi.conf --nfapi VNF

Afterwards, start and connect the PNF

sudo NFAPI_TRACE_LEVEL=info ./nr-softmodem -O ../../../targets/PROJECTS/GENERIC-NR-5GC/CONF/gnb-pnf.band78.rfsim.conf --nfapi PNF --rfsim

Finally, you can start the UE (observe the radio configuration info in the VNF!)

sudo ./nr-uesoftmodem -r 106 --numerology 1 --band 78 -C 3619200000 -O ue.conf

You should not observe a difference between nFAPI split and monolithic.

Status

All FAPI message can be transferred between VNF and PNF. This is because OAI uses FAPI with its corresponding messages internally, whether a split is in use or not.

The nFAPI split mode supports any radio configuration that is also supported by the monolithic gNB, with the notable exceptions that only numerologies of 15kHz and 30kHz (mu=0 and mu=1, respectively) are supported.

The VNF requests to be notified about every slot by the PNF. No delay management is employed as of now; instead, the PNF sends a Slot.indication to the VNF in every slot (in divergence from the nFAPI spec).

Currently, downlink transmissions work the same in monolithic and nFAPI. In uplink, we observe an increased number of retransmissions, which limits the MCS and hence the achievable throughput (which is limited to 10-20Mbps). We are still debugging the root cause of this.

After stopping the PNF, you also have to restart the VNF.

When using RFsim, the system might run slower than in monolithic. This is because the PNF needs to slow down the execution time of a specific slot, because it has to send a Slot.indication to the VNF for scheduling.

Configuration

Both PNF and VNF are run through the nr-softmodem executable. The type of mode is switched through the --nfapi switch, with options MONOLITHIC (default if not provided), VNF, PNF.

If the type is VNF, you have to modify the MACRLCs.tr_s_preference (transport south preference) to nfapi. Further, configure these options:

  • MACRLCs.remote_s_address (remote south address): IP of the PNF
  • MACRLCs.local_s_address (local south address): IP of the VNF
  • MACRLCs.local_s_portc (local south port for control): VNF’s P5 local port
  • MACRLCs.remote_s_portc (remote south port for data): PNF’s P5 remote port
  • MACRLCs.local_s_portd (local south port for control): VNF’s P5 local port
  • MACRLCs.remote_s_portd (remote south port for data): PNF’s P7 remote port

Note that any L1-specific section (L1s, RUs, RFsimulator-specific/IF7.2-specific configuration or other radios, if necessary) will be ignored and can be deleted.

If the type is PNF, you have to modify modify the L1s.tr_n_preference (transport north preference) to nfapi. Further, configure these options:

  • L1s.remote_n_address (remote north address): IP of the VNF
  • L1s.local_n_address (local north address): IP of the PNF
  • L1s.local_n_portc (local north port for control): PNF’s P5 local port
  • L1s.remote_n_portc (remote north port for control): VNF’s P5 remote port
  • L1s.local_n_portd (local north port for data): PNF’s P7 local port
  • L1s.remote_n_portd (remote north port for data): VNF’s P7 remote port

Note that this file should contain additional, L1-specific sections (L1s, RUs RFsimulator-specific/IF7.2-specific configuration or other radios, if necessary).

To split an existing config file monolithic.conf for nFAPI operation, you can proceed as follows:

  • copy monolithic.conf, which will be your VNF file (vnf.conf)
  • in vnf.conf
  • modify MACRLCs section to configure south-bound nFAPI transport
  • delete L1s, RUs, and radio-specific sections.
  • in gNBs section, select a sufficiently large ra_ResponseWindow if a UE does not connect with a message that the response window timed out: this is necessary because the PNF triggers the scheduler in the VNF in advance, which might make the RA window more likely to run out
  • copy monolithic.conf, which will be your PNF file (pnf.conf)
  • in pnf.conf
  • modify L1s section to configure north-bound nFAPI transport (make sure it matches the MACRLCs section for vnf.conf
  • delete all the gNBs, MACRLCs, security sections (they are not needed)
  • if you have root-level options in monolithic.conf, such as usrp-tx-thread-config or tune-offset, make sure to to add them to pnf.conf, or provide them on the command line for the PNF.
  • to run, proceed as described in the quick start above.

Note: all L1-specific options have to be passed to the PNF, and remaining options to the VNF.

Transport mechanisms between VNF and PNF

Currently, the VNF/PNF split supports three transport mechanisms between each other:

  1. Socket communication (either regular, or SCTP), this is the default

The socket type may be changed by editing nfapi_pnf_config_create() and nfapi_vnf_config_create(), in both of which _this->sctp = <value, 0 or 1>; indicate whether SCTP or regular sockets are to be used.

Note: The value of _this->sctp must be the same on the VNF and PNF. 2. Intel WLS Lib, which uses DPDK to achieve a shared memory communication between components. 3. nvIPC, which is used exclusively for the NVIDIA Aerial L1. Thus, it is only applicable for the VNF.

The change between transport mechanisms is done at compilation time: - No changes to the build_oai call are required in order to select socket communication, as it is the default. - In order to select WLS as the transport mechanism between VNF and PNF, first install the WLS library, and afterwards use -t WLS as a parameter of build_oai:

How to use nFAPI

nFAPI is used by default. Compile and configure as indicated above.

How to use Aerial

Refer to this document for more information.

How to use WLS lib

Before the first compilation with WLS support, the WLS library must first be compiled and installed to the system.

The WLS library has a few dependencies: - DPDK, specifically version 20.11.3. - libelf-dev - libhugetlbfs-dev

Additionally, a patch needs to be applied to the WLS lib Makefile in order for the shared library and headers to be installed into the system, the necessary patch is available here

Clone the code and apply the patch

git clone -b oran_f_release https://gerrit.o-ran-sc.org/r/o-du/phy.git
cd phy/wls_lib/
git apply ~/openairinterface5g/cmake_targets/tools/install_wls_lib.patch

Then compile and install the library

WIRELESS_SDK_TOOLCHAIN=gcc WIRELESS_SDK_TARGET_ISA=avx2 make
sudo WIRELESS_SDK_TOOLCHAIN=gcc WIRELESS_SDK_TARGET_ISA=avx2 make install

After installing WLS, you can run the build command as shown below:

./build_oai -t WLS -w USRP --gNB --nrUE --ninja -C
How to run OAI PNF with OAI VNF

Refer to the above steps in Quickstart, but run the PNF first as it is the WLS “master”.

How to run OAI PNF with OSC/Radisys O-DU

Set up the hugepages for DPDK (1GB page size, 6 pages; this only needs to be done once):

sudo nano /etc/default/grub
      GRUB_CMDLINE_LINUX_DEFAULT="${GRUB_CMDLINE_LINUX_DEFAULT} default_hugepagesz=1G hugepagesz=1G hugepages=6"

Then rewrite the bootloader and reboot

sudo update-grub
sudo reboot

Install dependencies:

sudo apt-get install libstdc++-14-dev libnsl-dev libpcap-dev libxml2-dev

Clone the Radisys repository (We’re currently using the oai_integration branch):

git clone https://gerrit.o-ran-sc.org/r/o-du/l2 -b oai-integration

Build the O-DU

cd ~/l2/build/odu
make clean_all;make odu PHY=INTEL_L1 MACHINE=BIT64 MODE=TDD;make cu_stub NODE=TEST_STUB MACHINE=BIT64 MODE=TDD;make ric_stub NODE=TEST_STUB MACHINE=BIT64 MODE=TDD

Setup local interfaces for the cu_stub, ric_stub and o_du

sudo ifconfig enp7s0:ODU "192.168.130.81" && sudo ifconfig enp7s0:CU_STUB "192.168.130.82" && sudo ifconfig enp7s0:RIC_STUB "192.168.130.80"

Run cu_stu and ric_stub in separate terminals

cd ~/l2/bin/
./cu_stub/cu_stub 
clear && ./ric_stub/ric_stub

Run the OAI PNF first, as it is the WLS memory master

sudo NFAPI_TRACE_LEVEL=info ./nr-softmodem -O ../../../targets/PROJECTS/GENERIC-NR-5GC/CONF/gnb-pnf.band78.rfsim.2x2.conf --nfapi PNF --rfsim --rfsimulator.serveraddr server

Run the O-DU over GDB

sudo -E gdb -ex run --readnever --args  ./odu/odu

Note: If you see the following prompt in GDB

This GDB supports auto-downloading debuginfo from the following URLs:
  <https://debuginfod.ubuntu.com>
Enable debuginfod for this session? (y or [n])

You can run the following command one time before executing gdb to disable it: 

export DEBUGINFOD_URLS=

Run the OAI-UE

sudo ./nr-uesoftmodem -r 273 --numerology 1 --band 78 -C 3400140000 --ssb 1518 --uicc0.imsi 001010000000001 --rfsim

nFAPI logging system

nFAPI has its own logging system, independent of OAI’s. It can be activated by setting the NFAPI_TRACE_LEVEL environment variable to an appropriate value; see the environment variables documentation for more info.

To see the (any) periodical output at the PNF, define NFAPI_TRACE_LEVEL=info. This output shows:

41056.739654 [I] 3556767424: nr_pnf_p7_get_msgs: [P7:1] msgs ontime 489 thr DL 0.06 UL 0.01 msg late 0 (vtime)
  • The first numbers are timestamps.
  • nr_pnf_p7_get_msgs is the name of the functions that prints the output.
  • [P7:1] refers to the fact that these are information on P7, of PHY ID 1. Finally, msgs ontime 489 means that in the last window (since the last print), 489 messages arrived at the PNF in total.
  • The combined throughput of TX_data.requests (DL traffic) was 0.06 Mbps; note that this includes SIB1 and other periodical data channels.
  • In UL, 0.01 Mbps have been sent through RX_data.indication. msg late 0 means that 0 packets have been late. This number is an aggregate over the total runtime, unlike the other messages.
  • Finally, (vtime) is a reminder that the calculations are done over virtual time, i.e., frames/slots as executed by the 5G Systems. For instance, these numbers might be slightly higher or slower in RFsim than in wall-clock time, depending if the system advances faster or slower than wall-clock time.